CNFULO伏龙同步带中型高扭矩型齿型STPD/STS-S8M(节距=8.00mm)标准规格表
CNFULO伏龙同步带中型高扭矩型齿型STPD/STS-S8M(节距=8.00mm)标准规格表规格节线长(mm)模宽(mm)齿数S8M-37637645047S8M-38438445048S8M-39239245049S8M-44044045055S8M-46446445058S8M-45645645057S8M-46446445058S8M-48048045060S8M-49649645062S8M-51251245064S8M-52052045065S8M-52852845066S8M-53653645067S8M-56056045070S8M-58458445073S8M-59259245074S8M-60060045075S8M-63263245079S8M-64064045080S8M-65665645082S8M-66466445083S8M-68068045085S8M-68868845086S8M-71271245089S8M-72072045090S8M-72872845091S8M-73673645092S8M-75275245094S8M-76076045095S8M-76876845096S8M-77677645097S8M-78478445098S8M-800800200100S8M-824824450103S8M-832832450104S8M-840840450105S8M-848848200106S8M-856856450107S8M-864864450108S8M-872872450109S8M-880880450110S8M-888888450111S8M-896896450112S8M-912912450114S8M-920920450115S8M-928928450116S8M-936936450117S8M-944944200118S8M-960960450120S8M-976976450122S8M-984984450123S8M-992992450124S8M-10001000450125S8M-10081008450126S8M-10161016450127S8M-10241024450128S8M-10321032450129S8M-10401040200130S8M-10561056450132S8M-10641064450133S8M-10721072450134S8M-10801080450135S8M-10961096450137S8M-11041104450138S8M-11201120450140S8M-11281128450141S8M-11361136450142S8M-11441144450143S8M-11521152450144S8M-11601160200145S8M-11681168450146S8M-11841184450148S8M-11921192450149S8M-12001200450150S8M-12081208450151S8M-12161216450152S8M-12241224450153S8M-12321232450154S8M-12401240450155S8M-12481248450156S8M-12561256450157S8M-12641264450158S8M-12721272450159S8M-12801280200160S8M-12961296450162规格节线长(mm)模宽(mm)齿数S8M-13041304450163S8M-13121312450164S8M-13201320450165S8M-13441344450168S8M-13521352450169S8M-13601360450170S8M-13841384450173S8M-13921392450174S8M-14001400450175S8M-14241424450178S8M-14321432450179S8M-14401440450180S8M-14801480450185S8M-15121512450189S8M-15201520450190S8M-15281528450191S8M-15361536450192S8M-15441544450193S8M-15521552450194S8M-16001600200200S8M-16241624450203S8M-16321632450204S8M-16481648450206S8M-16721672450209S8M-16801680450210S8M-16881688450211S8M-16961696450212S8M-17281728200216S8M-17601760450220S8M-17761776450222S8M-18001800450225S8M-18321832450229S8M-18401840450230S8M-18801880450235S8M-19121912450239S8M-20002000450250S8M-20242024450253S8M-20322032450254S8M-20482048450256S8M-21042104450263S8M-21202120440265S8M-21602160440270S8M-22002200450275S8M-22402240190280S8M-2812248450281S8M-22642264450283S8M-22722272450284S8M-23042304450288S8M-24002400450300S8M-24322432450304S8M-24802480450310S8M-24962496190312S8M-25362536180317S8M-25602560250320S8M-25842584450323S8M-26002600450325S8M-26802680450335S8M-28002800450350S8M-28322832450354S8M-28482848450356S8M-28802880450360S8M-30003000450375S8M-30483048450381S8M-32003200450400S8M-32803280450410S8M-34003400450425S8M-35603560440445S8M-36003600450450S8M-36803680450460S8M-37203720250465S8M-40004000450500S8M-40644064450508S8M-43204320450540S8M-44004400450550S8M-44804480450560S8M-46804680450585S8M-49364936450617S8M-50485048440631S8M-50805080450635S8M-51045104450638S8M-52645264450658S8M-53525352440669S8M-56005600450700S8M-56805680450710S8M-56965696450712S8M-58005800440725S8M-59765976450747S8M-66406640450830CNFULO伏龙同步带的保管、安装使用注意事项1、严禁将CNFULO伏龙同步带强行过度折断、弯曲、避免强力层损伤,失去使用价值。2、不得将CNFULO伏龙同步带长期处于不正常的弯曲状态存放。3、保存在阴凉处。4、安装时请缩短中心距,放松张紧轮,不得强行将同步带从同步带轮下凸挡边上硬拉拖磨装入。5、同步带轮的齿必须与同步带的运转方向直角。6、主动轮与被动轮的主轴的平行度就控制在正切=1/1000左右。轴位不准,直接影响使用寿命。7、发现主动轮上CNFULO伏龙同步带向一边偏位,应移动一下被动轮加以调整,并调整张紧轮的压力。8、在起动时,中心距改变,同步带松驰,发生跳齿现象,应检查同步带轮机架是否松动,轴的定位有否失准。加以调整、加固。9、CNFULO伏龙同步带安装时必须按不同同步带的型号和带宽适当的加以张紧力。10、张紧轮且一定要安装在带动的传动松边一侧。CNFULO伏龙同步带轻型高扭矩型STPD/STS-S5CNFULO伏龙同步带轻型高扭矩型STPD/STS-S4CNFULO伏龙同步带小型高扭矩型STPD/STS-S3CNFULO伏龙同步带精确齿高扭矩型STPD/STS-SCNFULO伏龙超重型同步带HTD-20M型(节距=20CNFULO伏龙同步带重型圆弧齿HTD-14M型(节距=CNFULO伏龙同步带中型圆齿HTD-8M型(节距=8.CNFULO伏龙同步带圆齿HTD-5M(节距=5.00m)