CARLISLE卡莱同步皮带采用标准安装要求和高扭矩S8M标准规格
CARLISLE卡莱橡胶同步皮带和传动带轮生产标准参照采用ISO5294-1979《同步带传动一带轮》。主题内容与适用范围CARLISLE卡莱橡胶同步皮带准规定了用来传递机械功率,正确***或实现同步运动的同步带传动中带轮的基本特征,包括:轮齿的尺寸及极限偏差、带轮的尺寸及极限偏差、带轮的形位公差。本标准适于一般工业用同步带轮,不适用汽车同步带轮。CARLISLE卡莱橡胶同步皮带引用标准:同步带传动术语同步带传动额定功率和传动中心距的计算带轮材质、表面粗糙度及平衡轮齿形状、尺寸及极限偏差带轮齿廓形状有渐开线齿廓和直边齿廓两种。a、渐开线齿廓刀具:加工渐开线齿廓刀具—齿条刀具的基本尺寸及极限偏差b、平行度:带轮触与轴孔的轴线平行,其公差值随是每毫米轮宽不大于O.OO1mm。轮宽小于lOmm时,以lOmm计算平行度。c、锥度:在给定的带轮外径公差范围内,每毫米轮宽的***大锥度t为O.OO1mm。当轮宽小于lOmm时,以lOmm计算锥度。d、带轮其它质量要求:带轮的材质表面粗糙度及平衡应符合GB11357-89《带轮的材质、表面粗糙度及平衡》。e、带轮的标记:带轮的标记由轮的齿数,带的型号和轮宽代号组成。CARLISLE卡莱橡胶同步皮带传动安装和使用要求带轮带轮挡圈可按下列情况选择带轮挡圈:a‘在二轴传动中,_二个带轮中必须有一个带轮两侧具有挡圈,或两带轮的不同侧边各有一个挡圈。b.在中心距超过小带轮直径的8倍以上:的传动中,一二个带轮的两侧应都有挡圈。c.在垂直轴传动中,其中一个带轮的两侧应有挡圈,而在系统中其他带轮仅在底部一侧有挡圈。d.在多轴传动中,应保证每隔一个带轮有二个挡圈,或围绕该系统每个带轮的对边各有一个挡圈。CARLISLE卡莱同步皮带轮安装要求CARLISLE卡莱同步皮带轮在安装时,必须注意带轮轴线的平行度,使各带轮的传动中心平面位于同一卜面内,防止因带轮偏斜,而使带侧压紧在挡圈上,造成带侧面磨损加剧,甚至带被挡圈切断。因此,对带轮偏斜V.须加以调整,可按图A1,把偏斜角8m调到允许范围内。在保证带轮的对准性的同时,应保证传动装置机架和轴的刚度。在使用带轮时,必须除去带轮上的锈蚀,以免过早磨损同步带。CARLISLE卡莱高性能高扭矩S8M橡胶同步带系列规格表同步皮带规格同步皮带节线长(mm)同步皮带模宽(mm)同步皮带齿数S8M-37637645047S8M-38438445048S8M-39239245049S8M-44044045055S8M-46446445058S8M-45645645057S8M-46446445058S8M-48048045060S8M-49649645062S8M-51251245064S8M-52052045065S8M-52852845066S8M-53653645067S8M-56056045070S8M-58458445073S8M-59259245074S8M-60060045075S8M-63263245079S8M-64064045080S8M-65665645082S8M-66466445083S8M-68068045085S8M-68868845086S8M-71271245089S8M-72072045090S8M-72872845091S8M-73673645092S8M-75275245094S8M-76076045095S8M-76876845096S8M-77677645097S8M-78478445098S8M-800800200100S8M-824824450103S8M-832832450104S8M-840840450105S8M-848848200106S8M-856856450107S8M-864864450108S8M-872872450109S8M-880880450110S8M-888888450111S8M-896896450112S8M-912912450114S8M-920920450115S8M-928928450116S8M-936936450117S8M-944944200118S8M-960960450120S8M-976976450122S8M-984984450123S8M-992992450124S8M-10001000450125S8M-10081008450126S8M-10161016450127S8M-10241024450128S8M-10321032450129S8M-10401040200130S8M-10561056450132S8M-10641064450133S8M-10721072450134S8M-10801080450135S8M-10961096450137S8M-11041104450138S8M-11201120450140S8M-11281128450141S8M-11361136450142S8M-11441144450143S8M-11521152450144S8M-11601160200145S8M-11681168450146S8M-11841184450148S8M-11921192450149S8M-12001200450150S8M-12081208450151S8M-12161216450152S8M-12241224450153S8M-12321232450154S8M-12401240450155S8M-12481248450156S8M-12561256450157S8M-12641264450158S8M-12721272450159S8M-12801280200160S8M-12961296450162同步皮带规格同步皮带节线长(mm)同步皮带模宽(mm)同步皮带齿数S8M-13041304450163S8M-13121312450164S8M-13201320450165S8M-13441344450168S8M-13521352450169S8M-13601360450170S8M-13841384450173S8M-13921392450174S8M-14001400450175S8M-14241424450178S8M-14321432450179S8M-14401440450180S8M-14801480450185S8M-15121512450189S8M-15201520450190S8M-15281528450191S8M-15361536450192S8M-15441544450193S8M-15521552450194S8M-16001600200200S8M-16241624450203S8M-16321632450204S8M-16481648450206S8M-16721672450209S8M-16801680450210S8M-16881688450211S8M-16961696450212S8M-17281728200216S8M-17601760450220S8M-17761776450222S8M-18001800450225S8M-18321832450229S8M-18401840450230S8M-18801880450235S8M-19121912450239S8M-20002000450250S8M-20242024450253S8M-20322032450254S8M-20482048450256S8M-21042104450263S8M-21202120440265S8M-21602160440270S8M-22002200450275S8M-22402240190280S8M-2812248450281S8M-22642264450283S8M-22722272450284S8M-23042304450288S8M-24002400450300S8M-24322432450304S8M-24802480450310S8M-24962496190312S8M-25362536180317S8M-25602560250320S8M-25842584450323S8M-26002600450325S8M-26802680450335S8M-28002800450350S8M-28322832450354S8M-28482848450356S8M-28802880450360S8M-30003000450375S8M-30483048450381S8M-32003200450400S8M-32803280450410S8M-34003400450425S8M-35603560440445S8M-36003600450450S8M-36803680450460S8M-37203720250465S8M-40004000450500S8M-40644064450508S8M-43204320450540S8M-44004400450550S8M-44804480450560S8M-46804680450585S8M-49364936450617S8M-50485048440631S8M-50805080450635S8M-51045104450638S8M-52645264450658S8M-53525352440669S8M-56005600450700S8M-56805680450710S8M-56965696450712S8M-58005800440725S8M-59765976450747S8M-66406640450830)