轮毂江苏NSK轴承单元的使用和使用也在不断增加。它已发展到第三代：

The use and use of hub Jiangsu NSK bearin it is also increasing. It has developed to the third generation:

***代是由双列角接触轴承。

The first generation is a double row angle contact bearing.

第二代，在滚道上有一个用于固定轴承的法兰。用螺母将轴承固定在轴上是容易的，因此易于维护。

The second generation has a flange for fixed bearings on the raceway. It is easy to fix the bearing on the axle with nuts, so it is easy to maintain.

第三代轮毂轴承单元装有轴承单元和ABS。

The third generation hub bearin it is equipped with bearin it and ABS.

轮毂单元具有内法兰和外法兰，内法兰螺栓与传动轴连接，外法兰用于整个江苏NSK轴承的安装。

The hub unit has inner flange and outer flange, the inner flange bolts are connected with the tran***ission shaft, and the outer flange is used for the installation of the entire NSK bearing in Jiangsu.

1。为了保证江苏NSK轴承***大的安全性和可靠性，建议在不考虑汽车老化的情况下定期检查车轮轴承，并有一个早期的磨损信号，包括任何旋转摩擦噪声或异常减速度。苏珊的养老金组合发生了变化。对于后轮驱动车辆，建议在车辆到达38000公里时润滑前轮江苏NSK轴承。更换制动系统时，检查轴承并更换油封。

1. In order to ensure the maximum safety and reliability of the Jiangsu NSK bearing, it is suggested that the wheel bearings be checked regularly without c***idering the aging of the car, and there is an early wear signal, including any rotating friction noise or abnormal speed reduction. Susan's pension portfolio has changed. For rear wheel drive vehicles, it is recommended to lubricate the front wheel Jiangsu NSK bearing when the vehicle reaches 38000 km. When replacing the brake system, check the bearing and replace the oil seal.

2，如果我们听到轮毂江苏NSK轴承部分的杂音，首先，找出噪声的位置是非常重要的。存在许多可能引起噪声的运动部件，或者在一些旋转部件和非旋转部件之间可能存在接触。如果轴承中有噪声，轴承可能损坏，需要更换。

2, if we hear the murmurs of Jiangsu NSK bearing part of the hub, first, finding out the location of the noise is very important. There are many moving parts that may cause noise, or there may be contact between some rotating parts and non rotating parts. If there is noise in the bearing, the bearing may be damaged and need to be replaced.

3，由于前轮轮毂江苏NSK轴承两侧的工作条件相似，即使只有一个轴承断裂，建议成对地更换它们。

3, because the working conditi*** on the two sides of the front wheel hub Jiangsu NSK are similar, even if only one bearing is broken, it is recommended to replace them in pairs.

4，轮毂江苏NSK轴承更敏感。在任何情况下，都需要正确的方法和正确的工具。轴承部件在贮存、运输和安装过程中不得损坏。有些轴承需要较大的压痕，所以需要特殊的工具。一定要参考汽车制造说明书。

4, the hub Jiangsu NSK bearing is more sensitive. In any case, correct methods and correct tools are needed. Bearing parts shall not be damaged during storage, transportation and installation. Some bearings require larger indentation, so special tools are needed. Be sure to refer to the automobile manufacturing instructi***.

5。安装江苏NSK轴承时，应保持在干净整洁的环境中。进入轴承的小颗粒也会缩短轴承的使用寿命。在更换轴承时，保持清洁的环境非常重要。不允许用锤子敲击轴承，注意不要将轴承落在地上（或类似的不当处理）。安装前应检查轴和轴承座的状况。即使轻微磨损也会导致兼容性差，导致轴承早期失效。

5. When installing Jiangsu NSK bearings, it should be kept in a clean and tidy environment. ***all particles entering the bearing will also shorten the service life of bearings. It is very important to maintain a clean environment when replacing bearings. It is not allowed to percussion bearings with a hammer, and be careful not to drop bearings on the ground (or similar improper handling). The condition of shaft and bearing seat should be checked before installation. Even slight wear can cause poor compatibility, resulting in early failure of bearings.

6。对于轮毂江苏NSK轴承单元，不要试图拆下轮毂轴承或调整轮毂单元的密封圈，否则会损坏密封圈，并会进入水或灰尘。甚至密封圈和内圈的滚道被损坏，导致轴承***失效。

6. For the hub Jiangsu NSK bearin it, do not try to remove the hub bearing or adjust the seal ring of the hub unit, otherwise it will damage the sealing ring and enter the water or dust. Even the raceway of the sealing ring and inner ring is damaged, resulting in permanent failure of the bearing.

 

文章来自：江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www.wh-skf.com

文章来自：江苏INA轴承 www.ina-china.cn

The article comes from: Jiangsu INA bearing www.ina-china.cn

文章来自：江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www.klbbearings.com