当江苏INA轴承被接受时，验收主要包括常规检查，如江苏INA轴承间隙尺寸的三个尺寸和尺寸精度。应该注意的是，无论什么样的检查方法，我们都必须严格遵守江苏INA轴承***标准。详细讨论了常规检查的方法。

When Jiangsu INA bearings are accepted, the acceptance mainly includes routine inspection, such as the three dimensi*** and dimensional accuracy of INA bearing clearance dimensi*** in Jiangsu. It should be noted that no matter what kind of inspection methods, we must strictly abide by the Jiangsu INA bearing national standa***. The method of routine inspection is discussed in detail.

1，允许测量误差

1, allowable measurement error

理论上，江苏INA轴承测量误差应控制在公差的10%以下。另外，为了保证测量数据的准确性，为了有效地控制测量误差，必须使用专用的测量工具。

Theoretically, the INA bearing measurement error in Jiangsu should be controlled below 10% of the tolerance. In addition, in order to ensure the accuracy of measurement data, in order to effectively control the measurement error, special measuring tools must be used.

2，实测面积调整

2, measured area adjustment

在测量江苏INA轴承时，测量区域的国内外标准存在一定的差异。通常，在环的两端测量倒角的两倍，而内需是环的南端***大的倒角坐标。

When measuring INA bearings in Jiangsu, there are some differences between the domestic and international standa*** of the measuring area. Usually, two times the chamfer angle is measured at both ends of the ring, and the internal demand is the largest chamfering coordinate at the southern end of the ring.

3，尺寸测量

3, size measurement

对于江苏INA轴承尺寸的测量，我们可以采用比较测量的方法来测量。根据规定，使用剂量块或标准件作为比较测量的基准。

For the measurement of the bearing size of Jiangsu INA, we can use the method of comparative measurement to measure. According to the regulati***, dosage blocks or standard parts are used as benchmark for comparative measurement.

4，温度调节

4, temperature regulation

当江苏INA轴承被检查和检查时，环境温度应控制在20摄氏度。此外，轴承、量块等可以放置在同一金属板上，从而可以在***短的时间内实现温度平衡。当然，为了保证测量结果的准确性，我们应该尽量避免用手直接测量，因为手上的温度会影响测量值。

When Jiangsu INA bearings are inspected and inspected, the ambient temperature should be controlled at 20 degrees Celsius. Besides, bearings, gauge blocks and so on can be placed on the same metal plate, so that the temperature balance can be realized in the shortest time. Of course, in order to ensure the accuracy of the measurement results, we should try to ***oid direct measurement by hand, because the temperature on the hand will affect the measured value.

5，负荷测量规程

5, the regulation of load measurement

江苏INA轴承检查，主要是起亚、KEA等十四项指标。特别是，在测量起亚时，需要施加必要的测量负载以确保稳定的测量值。

Jiangsu INA bearing inspection, mainly KIA, KEA and other fourteen indicators. In particular, when measuring KIA, it is necessary to apply the necessary measurement load to ensure a stable measurement value.

轴承装配前的检查是保证轴承稳定可靠、操作精度高的重要保证。同时，它对减少轴承故障的发生和达到预期的效果起着重要的作用。

Inspection before bearing assembly is an important guarantee for ensuring stable and reliable bearing and high operation accuracy. At the same time, it plays an important role in reducing the occurrence of bearing failures and achieving the desired results.

 

 

文章来自：江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www.wh-skf.com

文章来自：江苏INA轴承 www.ina-china.cn

The article comes from: Jiangsu INA bearing www.ina-china.cn

文章来自：江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www.klbbearings.com