阿托斯先导式溢流阀AGAM-10/10/35034溢流阀在装配或使用中，由于O形密封圈、组合密封圈的损坏，或者安装螺钉、管接头的松动，都可能造成不应有的外泄漏。如果锥阀或主阀芯磨损过大，或者密封面接触不良，还将造成内泄漏过大，甚至影响正常工作。电磁溢流阀常见的故障有先导电磁阀工作失灵、主阀调压失灵和卸荷时的冲击噪声等。后者可通过调节加置的缓冲器来减少或消除。如不带缓冲器，则可在主阀溢流口加一背压阀。（压力一般调至5kgf/cm2左右，即0.5MPa）。[1]先导式溢流阀AGAM-10/10/10034AGAM-10/10/100-IX230/50/60AC34AGAM-10/10/100-IX24DCAGAM-10/10/210AGAM-10/10/210/V-IX24DCAGAM-10/10/210-IX230/50/60ACAGAM-10/10/210-IX24DCAGAM-10/10/210-IX24DC34/WGAGAM-10/10/35034AGAM-10/10/350/V-IX24DCAGAM-10/10/350-1X24DC34AGAM-10/100AGAM-10/100AGAM-10/100/VAGAM-10/11/10034AGAM-10/11/100/7PA-M-AO24DCAGAM-10/11/100-IX230/50/60ACAGAM-10/11/210-IX230/50/60ACAGAM-10/11/210-IX24DCAGAM-10/11/350/PA-GK-AO24DC22AGAM-10/11/350-IX110/50/60ACAGAM-10/11/350-IX24DCAGAM-10/20/210/100-IX24DCAGAM-10/20/350/100-IX230/50/60AC34AGAM-10/20/350/210/V-IX230/50/60AC34AGAM-10/20/350/210-IX230/50/60AC34AGAM-10/20/350/210-IX24DC34AGAM-10/21/350/100-IX24DC34AGAM-10/21/350/210-IX230/50/60AC34AGAM-10/210AGAM-10/210/V34AGAM-10/22/100/100-IX24DC34AGAM-10/350AGAM-10/5034AGAM-20/10/100/V-IX24DC53AGAM-20/10/210/V-IX24DC53AGAM-20/10/210-IX230/50/60ACAGAM-20/10/210-IX24DCAGAM-20/10/350-IX230/50/60ACAGAM-20/10/350-IX24DCAGAM-20/100AGAM-20/11/210/M-AO22021AGAM-20/11/210/V-IX24DC53AGAM-20/11/210-IX230/50/60ACAGAM-20/11/210-IX24DCAGAM-20/11/350-IX24DC53AGAM-20/210AGAM-20/210/V53/WGAGAM-20/22/350/350-IX24DCAGAM-20/350AGAM-32/10/210-IX24DCAGAM-32/10/350-IX24DCAGAM-32/20/210/210/V-IX230/50/60AC53AGAM-32/20/210/210-IX230/50/60ACAGAM-32/20/350/210-IX24DC53AGAM-32/21053AGAM-32/350AGAM-32/350/V53ARAM-20/10/100/V-IX110/50/60AARAM-20/10/210-IX24DC72ARAM-20/10072ARAM-20/210ARAM-20/35072ARAM-32/11/210-IX110/50/60AC)