DAYCO岱高英制高精度同步带MXL（齿距=2.032MM）标准型号表规格节线长齿数规格节线长齿数规格节线长齿数40MXL101.65085MXL215.39106189MXL479.5523642MXL107.75388MXL223.52110192MXL487.6824043MXL109.735489MXL227.58112198MXL503.9424844MXL111.765591MXL231.65114200MXL508.0025045MXL113.795692MXL233.68115205MXL520.1925646MXL117.865894MXL239.78118208MXL528.3226047MXL119.895996MXL243.84120212MXL538.4826548MXL121.926097.6MXL247.9122221MXL560.8327650MXL128.026398MXL249.94123224MXL568.9628052MXL132.0865100MXL254125228MXL579.1228553MXL134.1166101MXL256.03126232MXL589.2829054MXL138.1868102.4MXL260.1128236MXL599.4429556MXL142.2470104MXL264.16130240MXL609.630057MXL144.2771105MXL266.19131244MXL619.7630558MXL146.372106MXL268.22132250MXL633.9831258.4MXL148.3473112MXL284.48140254MXL646.1831860MXL152.475115MXL292.61144256MXL650.2432061MXL154.4376117MXL298.7147258MXL656.3432361.6MXL156.4677118MXL300.74148259MXL658.3732463MXL160.5379120MXL304.8150262MXL666.532864MXL162.5680121MXL306.83151266MXL676.6633365MXL166.6282122MXL310.9153269MXL682.7533666MXL168.6683124MXL314.96155280MXL711.235068MXL172.7285126MXL321.06158290MXL735.5836269MXL176.7887128MXL325.12160292MXL741.6836570MXL178.8288129MXL327.15161302MXL768.137872MXL182.8890132MXL335.28165320MXL812.840073MXL186.9492136MXL345.44170362MXL920.545374MXL188.9893140MXL355.6175379MXL961.1447375MXL191.0194144MXL365.76180403MXL1024.1350476MXL193.0495152MXL386.08190418MXL1060.75221、严禁将DAYCO岱高MXL同步带强行过度折断、弯曲、避免强力层损伤，失去使用价值。2、不得将DAYCO岱高MXL同步带长期处于不正常的弯曲状态存放。3、将DAYCO岱高MXL同步带要保存在阴凉处。4、安装时请缩短中心距，放松张紧轮，不得强行将带从带轮下凸挡边上硬拉拖磨装入。5、DAYCO岱高MXL同步带轮的齿必须与带的运转方向直角。6、主动轮与被动轮的主轴的平行度就控制在正切=1/1000左右。轴位不准，直接影响使用寿命。7、发现主动轮上DAYCO岱高MXL同步带向一边偏位，应移动一下被动轮加以调整，并调整张紧轮的压力。8、在起动时，中心距改变，DAYCO岱高MXL同步带松驰，发生跳齿现象，应检查带轮机架是否松动，轴的***有否失准。加以调整、加固。9、DAYCO岱高MXL同步带安装时必须按不同的型号和带宽适当的加以张紧力。10、张紧轮且一定要安装在带动的传动松边一侧。)